B&K 50 Series II Bedienungsanleitung Seite 33
- Seite / 102
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
19
The setup parameters are: Range, High (Voltage limit), Low (Voltage limit), and Rise/Fall time.
Use the key to select each parameter, and use the numeric keypad to change the
value. Press to confirm the change.
Range
Use the numeric keypad to change the range. This value will also act as a limit to how much
current the load can be configured to. The adjustable ranges vary depending on the model.
See specifications for details.
High
This parameter refers to the voltage high limit for the automatic test mode. During automatic
test mode, the device under test (DUT) must be operating below the configured value for the
test to PASS upon completion. If the DUT operates above the configured value, the test will FAIL
upon completion.
Note: This parameter is used for Automatic Test Function ONLY.
Low
This parameter refers to the voltage low limit for the automatic test mode. During automatic
test mode, the DUT must be operating below the configured value for the test to PASS upon
completion. If the DUT operates above the configured value, the test will FAIL upon completion.
Note: This parameter is used for Automatic Test Function ONLY.
High-Rate / Low-Rate
Use the and keys to select either High-Rate or Low-Rate, then press .
Depending on the selection, the configurable range for the rise and fall times will be different.
Rise Up / Fall Down
These parameters define the slew rate of the load, which determines the rate at which the
input current to a module changes to a new programmed value. You can set the current level’s
rise/fall slew rate on the front panel or by remote operation. The programmed slew rate is
immediately in effect to the triggered and transient current level changes.
Slew Rate Measurement and Actual Transition time
- Model: 8600, 8601, 8602 1
- Safety Summary 3
- AC line 4
- Compliance Statements 9
- CE Declaration of Conformity 10
- Safety Symbols 11
- Table of Contents 12
- 1 General Information 15
- 1.2 Package Contents 16
- 1.3 Product Dimensions 16
- Figure 2 - Rear View 18
- 1.4 Rackmount Installation 19
- 1.5 Front Panel Overview 20
- 1.6 Rear Panel Overview 21
- 80.000V 22
- 12.000A 22
- 2 Getting Started 24
- Fuse Requirements 25
- Fuse Replacement 25
- 2.2 Input Connections 26
- System Selftest . . . 27
- Input Check 28
- 3 Front Panel Operation 30
- SYSTEM MENU 31
- Constant Current 32
- Constant Voltage (CV) Mode 34
- Constant Voltage 35
- Constant Resistance 36
- Constant Power (CW) Mode 37
- Constant Power 38
- INITIALIZE SYSTEM? 40
- Configure Power-On State 41
- Load On Knob 41
- Configure Trigger Source 41
- Display Input On Timer 45
- DISPLAY ON TIMER 46
- COMMUNICATION 47
- CONFIG MENU 49
- VON LATCH 51
- PROTECT MENU 52
- CR LED Function 58
- Remote Sense 59
- External Voltage Source 61
- 3.5 Short Operation 62
- 3.6 Transient Operation 63
- TRANSITION 65
- 3.7 List Operation 68
- EDIT LIST 69
- 3.8 Battery Test Function 72
- 10.000V 73
- EDIT PROGRAM 76
- PROGRAM 76
- RECALL PROGRAM 80
- OCP TEST 84
- OPP TEST 87
- 4 Remote Operation 90
- 4.2 Remote Commands 91
- 5 Troubleshooting Guide 92
- 6 Specifications 94
- (excludes 97
- 7 Calibration 98
- INFORMATION 100
- LIMITED THREE-YEAR WARRANTY 101
Verwandte Produkte und Handbücher für Messen, Testen & Steuern B&K 50 Series II
(12 Seiten)Netgear EVA700 manuály
Uživatelské manuály a uživatelské příručky pro Přehrávače digitálních médií Netgear EVA700.
Poskytujeme 1 manuály pdf Netgear EVA700 ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Kommentare zu diesen Handbüchern